Identifying Scratches

Sanding, rusticating, sandblasting, buffing, etc. All here.
Post Reply
User avatar
PeskyPrussian
Posts: 41
Joined: Tue Sep 15, 2015 6:59 pm
Location: Ogden, Utah

Identifying Scratches

Post by PeskyPrussian »

Hello All,

Now that I've gotten a few pipes under my belt I'm trying to identify specific parts of my technique to improve upon. The largest
of all is probably my ability to identify tool marks and scratches while I'm sanding. In just about every pipe I've made I tried my
level best to remove all tool marks and various scratches before I continue with the finishing process. No matter how closely I look
there seems to be scratches that I only notice in the staining phase. I typically use a bright light at an angle to try and catch the
shadows to examine the surface of the briar, but this doesn't seem to be enough.

Does anyone have tips or techniques to help ensure that scratches don't make it through the finishing process?

Thanks in advance, this place has been an invaluable resource. :notworthy:
Adam Bybee
bybee_pipes - instagram
User avatar
sandahlpipe
Posts: 2106
Joined: Mon Feb 04, 2013 8:49 pm
Location: Zimmerman, MN
Contact:

Re: Identifying Scratches

Post by sandahlpipe »

Water soaks in more where the area is less well sanded. If you wet the stummel with a damp rag and notice some spots are drying slower, those are going to be the spots to go over more. Wiping with water also removes dust stuck between pores and helps you see where you're at. Of course, if your briar is fully dried, the difference will be more noticeable.

If you notice scratches when staining, just go back and sand them off and sand the stain off evenly all around and reapply the same color again. A lot of guys stain early in the process just to see where they're at with sanding.
---
Fail early, fail often. Your success depends on it.

Jeremiah Sandahl
http://sandahlpipe.com
User avatar
PeskyPrussian
Posts: 41
Joined: Tue Sep 15, 2015 6:59 pm
Location: Ogden, Utah

Re: Identifying Scratches

Post by PeskyPrussian »

That's a great tip, I appreciate the response. *Crosses Fingers* Here's to no missed scratches on this next pipe.
Adam Bybee
bybee_pipes - instagram
LatakiaLover
Posts: 3120
Joined: Sun Sep 02, 2007 4:29 am
Location: Kansas City, USA
Contact:

Re: Identifying Scratches

Post by LatakiaLover »

Sanding tip (though not specifically scratch related:

Add a teaspoon or so of some natural-ish brown stain to a jar of denatured alcohol (enough to get a faint color on raw wood) and then wash the pipe with it before sanding, and again between each grit as you climb finer.

It will make things go faster because you won't have to keep guessing where you've been, AND it will help prevent mis-shaping that's the result OF lingering too long in some areas and skipping others.
UFOs must be real. There's no other explanation for cats.
User avatar
PremalChheda
Posts: 1213
Joined: Sat Dec 11, 2010 6:03 pm
Location: Columbus, Ohio, USA
Contact:

Re: Identifying Scratches

Post by PremalChheda »

Buff lightly between sanding steps. You will see the scratches clearly.
Premal Chheda
http://www.chhedapipes.com - Just for fun
http://www.smokershaven.com - New & Estate Pipes
http://www.rawkrafted.com - Pipe Making Tools, Materials, & Supplies
User avatar
d.huber
Posts: 2691
Joined: Mon Dec 12, 2011 9:28 pm
Location: Durham, NC
Contact:

Re: Identifying Scratches

Post by d.huber »

Speaking for myself, I still encounter some scratches late in the game and I do just what Jeremiah suggested, which is sand the scratches away and restain the area.

Try not to get too frustrated with the scratches. You'll get better at eliminating them with time and practice.

Sent from my SCH-I545 using Tapatalk
http://www.dshpipes.com

"Strive for excellence, not for what someone else accepts."
-Tyler Beard
User avatar
PeskyPrussian
Posts: 41
Joined: Tue Sep 15, 2015 6:59 pm
Location: Ogden, Utah

Re: Identifying Scratches

Post by PeskyPrussian »

All good ideas, thanks guys.
Adam Bybee
bybee_pipes - instagram
Charl
Posts: 1901
Joined: Mon Jan 07, 2008 3:03 pm
Location: South Africa

Re: Identifying Scratches

Post by Charl »

I'm one of the guys that stain early on. When I finish with disc sanding, before starting by hand, I put a layer of stain on. That way you notice the scratches easily, as well as as high and low points. One other tip (maybe stupid to some): with every grit, make sure that you sand all surfaces and that all visible scratches are out.
Post Reply