bevel on top of bowl

For discussion of the drilling and shaping of the stummel.
Post Reply
notow1
Posts: 218
Joined: Mon Apr 15, 2013 10:09 pm
Location: Lake Zurich, Illinois

bevel on top of bowl

Post by notow1 »

Has Anyone tried using a handball with a course scotch brite pad? I have a hard time getting the sand paper to sit right on the ball and thought a scotch brite pad might form to the ball a little better. If Anyone has tried this I would appreciate some feedback on the results, thanks, Norm.
User avatar
baweaverpipes
The Awesomer
Posts: 947
Joined: Tue Dec 19, 2006 8:07 am
Location: Franklin, Tennessee
Contact:

Re: bevel on top of bowl

Post by baweaverpipes »

Cut a round disc of 120 grit sandpaper (about the size of a quarter), slot the disc with 6 or 8 slots, use your dremel by going into the bowl about 1/4", then hand sand with 400 grit.
You could do that, or use a round file by going around the bowl, then sand.
mcgregorpipes
Posts: 177
Joined: Sat May 12, 2012 9:07 pm
Location: Manitoba, Canada
Contact:

Re: bevel on top of bowl

Post by mcgregorpipes »

baweaverpipes wrote:Cut a round disc of 120 grit sandpaper (about the size of a quarter), slot the disc with 6 or 8 slots, use your dremel by going into the bowl about 1/4", then hand sand with 400 grit.
You could do that, or use a round file by going around the bowl, then sand.
i'm going to try that sand paper trick

for making a slight chamfer at the top of the chamber I've been using one of these to make a clean edge
http://www.amazon.com/dp/B00843WHYM/ref ... nkCode=asn

a hardball is maybe 2" in diameter? sounds like you're going for a wide bevel over the entire top of the bowl? would try it on a padded 5" sanding disc if you have one
Charl
Posts: 1901
Joined: Mon Jan 07, 2008 3:03 pm
Location: South Africa

Re: bevel on top of bowl

Post by Charl »

or use a squash ball, with paper wrapped around.
socrates
Posts: 316
Joined: Tue Dec 31, 2013 1:32 pm
Location: Oahu, Hawaii, USA

Re: bevel on top of bowl

Post by socrates »

I used to make custom fishing rods. In making grips from scratch I would make my own reamers from disgarded sections of rod blanks. Applied epoxy glue to them and then grit needed into the glue. Once set they worked better than commercially made reamers. The same could be done with wood balls in a selection of sizes to meet your needs.

Sent from my HTC0P3P7 using Tapatalk
mcgregorpipes
Posts: 177
Joined: Sat May 12, 2012 9:07 pm
Location: Manitoba, Canada
Contact:

Re: bevel on top of bowl

Post by mcgregorpipes »

what did you use for the abrasive?
socrates
Posts: 316
Joined: Tue Dec 31, 2013 1:32 pm
Location: Oahu, Hawaii, USA

Re: bevel on top of bowl

Post by socrates »

I would buy the abrasive from a rod parts supply like Mudhole or similar.

Sent from my HTC0P3P7 using Tapatalk
socrates
Posts: 316
Joined: Tue Dec 31, 2013 1:32 pm
Location: Oahu, Hawaii, USA

Re: bevel on top of bowl

Post by socrates »

I found a place called "The Rock Shop". They have abrasives in various grits for rock polishing. I ordered a selection I plan on gluing to various size wooden balls and testing.

Sent from my HTC0P3P7 using Tapatalk
caskwith
Posts: 2196
Joined: Sat Dec 08, 2007 6:00 am

Re: bevel on top of bowl

Post by caskwith »

You know a lot of the experimenting and testing could be saved if you did the bevel before taking it off the lathe ;)
User avatar
oklahoma red
Posts: 1084
Joined: Tue Apr 12, 2011 6:14 pm

Re: bevel on top of bowl

Post by oklahoma red »

You know a lot of the experimenting and testing could be saved if you did the bevel before taking it off the lathe ;)
+1

btw Chris, congrats on 1000 posts.

Chas.
User avatar
d.huber
Posts: 2691
Joined: Mon Dec 12, 2011 9:28 pm
Location: Durham, NC
Contact:

Re: bevel on top of bowl

Post by d.huber »

oklahoma red wrote:
You know a lot of the experimenting and testing could be saved if you did the bevel before taking it off the lathe ;)
+1

btw Chris, congrats on 1000 posts.

Chas.
http://www.dshpipes.com

"Strive for excellence, not for what someone else accepts."
-Tyler Beard
caskwith
Posts: 2196
Joined: Sat Dec 08, 2007 6:00 am

Re: bevel on top of bowl

Post by caskwith »

Woohoo 1000 posts!
caskwith
Posts: 2196
Joined: Sat Dec 08, 2007 6:00 am

Re: bevel on top of bowl

Post by caskwith »

Spoiled it :(
yachtexplorer
Posts: 42
Joined: Wed Nov 07, 2012 11:45 pm

Re: bevel on top of bowl

Post by yachtexplorer »

I use a 1" countersink mounted into the headstock of my lathe. My lathe is a variable speed 8/18 South Bend so I set the RPMs at around 400. I then hold the strummel in my hand, keep it parallel and square to the countersink and bevel the inner edge of the rim nice and slowly. You might practice a few times with a piece of scrap to make sure you have the sight lines right. Use two hands and set the bevel a little bit at a time.

Image
Image
Post Reply