Checked search but can't find anything specifically.
I'm using a dark blue stain and when I apply it I'm having issues.when I make a pass and then make another pass next to the stain I just put down, where the two passes meet I get a dark streak. I thinks its from the first pass flashing the da off before the stain next to it gets put on. So its acting like a double coat at the junction. What can I do to mitigate this? Or can I do something before buffing that knocks these darker areas down so the color looks uniform?
Overlap marks when staining
-
- Posts: 177
- Joined: Fri Apr 24, 2015 2:34 pm
Overlap marks when staining
Acting like a loon in the front yard, close to the road.
- baweaverpipes
- The Awesomer
- Posts: 947
- Joined: Tue Dec 19, 2006 8:07 am
- Location: Franklin, Tennessee
- Contact:
Re: Overlap marks when staining
If this is the under-coat, soak the sucker with stain. Then you can sand and/or buff.
Re: Overlap marks when staining
Or wash the whole pipe with sealer as soon as you've stained, to even it out. Depends on what you are trying to accomplish.
ALL YOUR PIPE ARE BELONG TO US!
-
- Posts: 177
- Joined: Fri Apr 24, 2015 2:34 pm
Re: Overlap marks when staining
Well. I'm sanding to 600 grit. Applying the stain, the shellac with da coat, the red trip, white dia, and finally carnuba buff.
I'm not familiar with doing it any other way at the moment.
I'm not familiar with doing it any other way at the moment.
Acting like a loon in the front yard, close to the road.
- baweaverpipes
- The Awesomer
- Posts: 947
- Joined: Tue Dec 19, 2006 8:07 am
- Location: Franklin, Tennessee
- Contact:
Re: Overlap marks when staining
Search finishing techniques.clickklick wrote:Well. I'm sanding to 600 grit. Applying the stain, the shellac with da coat, the red trip, white dia, and finally carnuba buff.
I'm not familiar with doing it any other way at the moment.
- PremalChheda
- Posts: 1213
- Joined: Sat Dec 11, 2010 6:03 pm
- Location: Columbus, Ohio, USA
- Contact:
Re: Overlap marks when staining
IAWBbaweaverpipes wrote:Search finishing techniques.clickklick wrote:Well. I'm sanding to 600 grit. Applying the stain, the shellac with da coat, the red trip, white dia, and finally carnuba buff.
I'm not familiar with doing it any other way at the moment.
You need to do some research and experimentation on finishing. Have you tested to see if stain comes off with heat, moisture, friction, etc..?
Premal Chheda
http://www.chhedapipes.com - Just for fun
http://www.smokershaven.com - New & Estate Pipes
http://www.rawkrafted.com - Pipe Making Tools, Materials, & Supplies
http://www.chhedapipes.com - Just for fun
http://www.smokershaven.com - New & Estate Pipes
http://www.rawkrafted.com - Pipe Making Tools, Materials, & Supplies
-
- Posts: 177
- Joined: Fri Apr 24, 2015 2:34 pm
Re: Overlap marks when staining
So I based most of my actions from here, viewtopic.php?f=35&t=10401
For this pipe, I don't want contrast so I'm not doing an undercoat. So I stain it with blue, after 220, sand all scratches and all stain goes away except for on the grain. Then stain again, sand with 320. Again with 400. Then after 400 I don't stain and just sand to 600. I then apply my final stain of blue which I was understanding as the topcoat. I then seal it with a shellac da mix before buffing.
What am I missing? Your responses make me think I'm missing something obvious. As for the pipes I've made, they are durable, color darkening but not fading. It does not rub off although I haven't tried it with wet handss. The wax dulls after a while but the stain will not come off on my fingers. But I've only made 19 pipes so far so maybe I've interpreted the information wrong and have been doing it incorrectly this whole time.
For this pipe, I don't want contrast so I'm not doing an undercoat. So I stain it with blue, after 220, sand all scratches and all stain goes away except for on the grain. Then stain again, sand with 320. Again with 400. Then after 400 I don't stain and just sand to 600. I then apply my final stain of blue which I was understanding as the topcoat. I then seal it with a shellac da mix before buffing.
What am I missing? Your responses make me think I'm missing something obvious. As for the pipes I've made, they are durable, color darkening but not fading. It does not rub off although I haven't tried it with wet handss. The wax dulls after a while but the stain will not come off on my fingers. But I've only made 19 pipes so far so maybe I've interpreted the information wrong and have been doing it incorrectly this whole time.
Acting like a loon in the front yard, close to the road.
- PremalChheda
- Posts: 1213
- Joined: Sat Dec 11, 2010 6:03 pm
- Location: Columbus, Ohio, USA
- Contact:
Re: Overlap marks when staining
Only couple things. Put first color on after either 320 or 400. Then sand up to either 600, 800, or 1000. Then top color, then shellac. Allow time to set. Then buff.clickklick wrote:So I based most of my actions from here, viewtopic.php?f=35&t=10401
For this pipe, I don't want contrast so I'm not doing an undercoat. So I stain it with blue, after 220, sand all scratches and all stain goes away except for on the grain. Then stain again, sand with 320. Again with 400. Then after 400 I don't stain and just sand to 600. I then apply my final stain of blue which I was understanding as the topcoat. I then seal it with a shellac da mix before buffing.
What am I missing? Your responses make me think I'm missing something obvious. As for the pipes I've made, they are durable, color darkening but not fading. It does not rub off although I haven't tried it with wet handss. The wax dulls after a while but the stain will not come off on my fingers. But I've only made 19 pipes so far so maybe I've interpreted the information wrong and have been doing it incorrectly this whole time.
For testing. Smoke the crap out of the pipe, then wipe with white cloth or paper towel while it is warm.
Premal Chheda
http://www.chhedapipes.com - Just for fun
http://www.smokershaven.com - New & Estate Pipes
http://www.rawkrafted.com - Pipe Making Tools, Materials, & Supplies
http://www.chhedapipes.com - Just for fun
http://www.smokershaven.com - New & Estate Pipes
http://www.rawkrafted.com - Pipe Making Tools, Materials, & Supplies
-
- Posts: 177
- Joined: Fri Apr 24, 2015 2:34 pm
Re: Overlap marks when staining
Thanks. I tried applying it with a brush instead if a pipe cleaner or q tip. I think blue is just not a nice color unless you go dark dark. I don't have this issue with lighter colors. I'll keep working on my technique.
Acting like a loon in the front yard, close to the road.