Temporarily Attaching Bamboo
Temporarily Attaching Bamboo
Up to now when making a pipe with bamboo to stummel transition sans spacer, I've temporarily attached the bamboo to the stummel with a tiny drop of CA glue on the face of the bamboo. Once the stummel is ready for stain I carefully break the glue hold and commence. This works well most of the time but on occasion I'll have to reface the bamboo to get rid of the little glue spot and have a gap free fit again.
A question for the group- how do you go guys temporarily attach bamboo to the shank? Is there another method I'm overlooking? Or do you typically finish with your bamboo attached?
Thanks!
-Josh
A question for the group- how do you go guys temporarily attach bamboo to the shank? Is there another method I'm overlooking? Or do you typically finish with your bamboo attached?
Thanks!
-Josh
Re: Temporarily Attaching Bamboo
I normally use a tiny spit of a drop of CA on the stainless steel, not the face. But only if it is really needed. Most of the time the fit is tight enough to keep the bamboo in place while shaping.
Re: Temporarily Attaching Bamboo
Like Charl friction is normally enough until time comes that it needs to be permanently fixed for the final finish work.
Re: Temporarily Attaching Bamboo
Ok, interesting, just a friction fit works for you guys. I've tried that before and had a problem with the bamboo shifting on occasion, even with a pretty tight mortise-tenon fit.
Re: Temporarily Attaching Bamboo
A bit of shellac will also make a temporary bond which breaks with a little torque. I use this method for heavy filing with my stem shank junctions. Stronger than a friction fit but not a whole lot.
DocAitch
DocAitch
"Hettinger, if you stamp 'hand made' on a dog turd, some one will buy it."
-Charles Hollyday, pipe maker, reluctant mentor, and curmudgeon
" Never show an idiot an unfinished pipe!"- same guy
-Charles Hollyday, pipe maker, reluctant mentor, and curmudgeon
" Never show an idiot an unfinished pipe!"- same guy
Re: Temporarily Attaching Bamboo
Okay, good to know. Have you noticed any residue left behind that affects the 'flushness' of the fit after you break the bond?
Re: Temporarily Attaching Bamboo
I have not noted a residue, but I have only used this method with flush fit stems, where I have attempted to finish (with stain and shellac) the shank face prior to final shaping.
I think that a couple of swipes with rough sand paper would be appropriate for the surfaces that will be mated with epoxy.
DocAitch
I think that a couple of swipes with rough sand paper would be appropriate for the surfaces that will be mated with epoxy.
DocAitch
"Hettinger, if you stamp 'hand made' on a dog turd, some one will buy it."
-Charles Hollyday, pipe maker, reluctant mentor, and curmudgeon
" Never show an idiot an unfinished pipe!"- same guy
-Charles Hollyday, pipe maker, reluctant mentor, and curmudgeon
" Never show an idiot an unfinished pipe!"- same guy
Re: Temporarily Attaching Bamboo
I gotcha, thanks for the tip.
Re: Temporarily Attaching Bamboo
If you use a blob of neat shellac as mentioned it would be removable with some IPA. FWIW superglue can be dissolved with acetone.
Re: Temporarily Attaching Bamboo
Thanks Chris, that's good to know. That could be the solution to the problem.
Re: Temporarily Attaching Bamboo
Shellac removable with beer? I'd rather not waste good stuff!
-
- Posts: 1767
- Joined: Mon Jun 11, 2012 9:43 pm
- Location: Missouri
- Contact:
Re: Temporarily Attaching Bamboo
I have discovered that a good Stout works way better than a crappy ol' IPACharl wrote:Shellac removable with beer? I'd rather not waste good stuff!
Am I Calamity Jane or Annie Oakley??...depends on the day.
www.ladybriar.com
www.ladybriar.com