Hi everyone-
For a long time now I have been trying to figure out how to create a "twisted shank" such as many Radice pipes tend to have. In case you aren't sure what the heck I'm talking about, here is a picture of the type of shank I'm referring to (found on google):
Is this technique acheived using a lathe, or is it necessary to hand carve a corkscrew shape such as that by hand?
Thanks for the advice!
Questions about the "twisted shank"
- SimeonTurner
- Site Supporter
- Posts: 750
- Joined: Wed Dec 24, 2008 7:46 pm
- Location: Denver, Colorado
- Contact:
I make that type of fluting on knife handles, but only by hand. I use round "chain saw" files because they have a constant diameter, i.e. no taper. It looks like that pipe has two flutes.
You draw the spiral where you want it with pencil, then go at it with files. If you have a steady hand, you could probably manage it with an appropriately shaped dremel bit.
You draw the spiral where you want it with pencil, then go at it with files. If you have a steady hand, you could probably manage it with an appropriately shaped dremel bit.
Regards,
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett
My thoughts exactly. Clean the thing up after filing with sandpaper wrapped on a dowel...Frank wrote:I make that type of fluting on knife handles, but only by hand. I use round "chain saw" files because they have a constant diameter, i.e. no taper. It looks like that pipe has two flutes.
You draw the spiral where you want it with pencil, then go at it with files. If you have a steady hand, you could probably manage it with an appropriately shaped dremel bit.
As you can see from Part 2, the lathe is just used to hand rotate the workpiece.Catch wrote:This may give you some idea's on layout.
http://www.youtube.com/watch?v=LDw_X14W4RI
Since a knife handle/pipe shank is somewhat smaller than that finial, I use cotton thread, attached with a tiny drop of super glue, to initially mark out the spiral.
Regards,
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett
- SimeonTurner
- Site Supporter
- Posts: 750
- Joined: Wed Dec 24, 2008 7:46 pm
- Location: Denver, Colorado
- Contact:
- SimeonTurner
- Site Supporter
- Posts: 750
- Joined: Wed Dec 24, 2008 7:46 pm
- Location: Denver, Colorado
- Contact:
I thought I would return to this thread to share my success with the twisted shank attempt! Thanks to everyone who contributed to helping me figure it out!
This pipe is a gift for a good friend who is getting married next week. I'm giving it to him at his bachelor party tomorrow, so I feel safe posting this today knowing there is about a .0001% chance he would see it.
This pipe is a gift for a good friend who is getting married next week. I'm giving it to him at his bachelor party tomorrow, so I feel safe posting this today knowing there is about a .0001% chance he would see it.
"It is noble to be good; it is still nobler to teach others to be good - and less trouble."
Turner Pipes Website:
http://www.turnerpipes.com
Of Briar and Ashes:
http://turnerpipes.wordpress.com
Turner Pipes Website:
http://www.turnerpipes.com
Of Briar and Ashes:
http://turnerpipes.wordpress.com
Charles Neil is the man!!! I love his minishows on Youtube... I was wondering if any other forum-mate is watchin 'em too...
Got thoughts? http://grandiflorum.net
- LexKY_Pipe
- Posts: 875
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: Lexington, Kentucky USA