Modifying the slot of a preform pipe stem - with video!
- KurtHuhn
- Site Admin
- Posts: 5326
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: United States/Rhode Island
Modifying the slot of a preform pipe stem - with video!
I made this for another forum member to demonstrate how I modify the slot on preform stems to make them smoke better.
Re: Modifying the slot of a preform pipe stem - with video!
Nicely done Kurt.
Thank you.
Todd
Thank you.
Todd
Re: Modifying the slot of a preform pipe stem - with video!
Confoundit all, Kurt! Where was that video yesterday when I was finishing up my first pipe of the year!
Great video. I had no clue the funnel needed to start that far back in the stem. I always work on the slot of my pre-molded stems, but not to this extent.
Thanks for another great resource!
Great video. I had no clue the funnel needed to start that far back in the stem. I always work on the slot of my pre-molded stems, but not to this extent.
Thanks for another great resource!
- KurtHuhn
- Site Admin
- Posts: 5326
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: United States/Rhode Island
Re: Modifying the slot of a preform pipe stem - with video!
Technically speaking, it doesn't have to start that far back, but that's just the way I've always done it. It would be perfectly acceptable to start it about an inch in instead of the inch and a half that I normally do. Really, as long as you get good airflow, no whistles, and no gurgles, it's all good.
Re: Modifying the slot of a preform pipe stem - with video!
Thank you! Lots of help! Great info!
Re: Modifying the slot of a preform pipe stem - with video!
Thanks again Kurt for another great video. For the brand new guy who's about to cut into his first piece of briar, I noticed that you talked about the continual airflow (without angles and obstructions) through the stem makes for no gurgles, etc. As I have understood so far from this forum - my first few attempts at a pipe should concentrate on "a good smoking pipe" then worry about how ugly they are... So, I guess my question is - engineering wise - assuming I have correctly seated a delrin tenon into my stem, and followed the airflow patterns in the stem as shown above - how much of a gap should there be between the mortise and tenon? Should they be flush mounted with a countersunk tenon or should there be a "moisture trap" as there seem to be on some of my (purchased) pipes and some famous factory diagrams? It seems that several of my (purchased) pipes are all over the place on this regard.
New Guy Disclaimer: After reading a lot of posts on drilling, engineering, etc... I've re-drilled holes in the shank, tenon and stem to 5/32 (tapering the hole in the bit with a lot of curled up sand paper) on one of my factory cheapies straight Dublins, and... it now smokes better than my most expensive named brand (ugh). Evidently, some of you might know what you're talking about
JK
New Guy Disclaimer: After reading a lot of posts on drilling, engineering, etc... I've re-drilled holes in the shank, tenon and stem to 5/32 (tapering the hole in the bit with a lot of curled up sand paper) on one of my factory cheapies straight Dublins, and... it now smokes better than my most expensive named brand (ugh). Evidently, some of you might know what you're talking about
JK
Re: Modifying the slot of a preform pipe stem - with video!
I'm still waiting for the first comment about sexy voice and lack of chaps. It is not a proper thread until we get there.
(Very nice video, by the way.)
(Very nice video, by the way.)
- KurtHuhn
- Site Admin
- Posts: 5326
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: United States/Rhode Island
Re: Modifying the slot of a preform pipe stem - with video!
You can have a small gap there with no ill effect. For years I used a 5/16" forstner bit to make a flat bottom, then went to great pains to ensure zero gap - but all that bought me was a lot of fiddly-time. You can drill the mortis with a regular drill bit, then get the tenon length "very close", then countersink the end of the tenon to smooth the air flow. This smokes just as well, if not better, than trying to make it perfect.jdkearns wrote:So, I guess my question is - engineering wise - assuming I have correctly seated a delrin tenon into my stem, and followed the airflow patterns in the stem as shown above - how much of a gap should there be between the mortise and tenon? Should they be flush mounted with a countersunk tenon or should there be a "moisture trap" as there seem to be on some of my (purchased) pipes and some famous factory diagrams? It seems that several of my (purchased) pipes are all over the place on this regard.
Imagine that!Evidently, some of you might know what you're talking about
- KurtHuhn
- Site Admin
- Posts: 5326
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: United States/Rhode Island
Re: Modifying the slot of a preform pipe stem - with video!
By the way, I'm not so sure I'm up to appearing in an Internet video wearing chaps. I could actually become some sort of meme dealing with my hairy behind and the fact that all chaps are assless - otherwise they would be pants. Or worse... two chaps, one Kurt....
Oh, I think I just grossed myself out. Now I need a drink...
Oh, I think I just grossed myself out. Now I need a drink...
Re: Modifying the slot of a preform pipe stem - with video!
Oh man, I should have clarified I meant about pipe-crafting, not assless pants videos you "chaps" are talking about.jdkearns wrote:Thanks again Kurt for another great video...
Evidently, some of you might know what you're talking about
JK
Re: Modifying the slot of a preform pipe stem - with video!
Thanks for great video!
That drill bit looks really flexible. All my thin drill bits are really stiff and brittle, do you use any special kind?
/Jon
That drill bit looks really flexible. All my thin drill bits are really stiff and brittle, do you use any special kind?
/Jon
- KurtHuhn
- Site Admin
- Posts: 5326
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: United States/Rhode Island
Re: Modifying the slot of a preform pipe stem - with video!
I forget where I got that bit - probably McMaster-Carr. It might appear flexible in the video, but it really isn't. It's an optical illusion created by me moving my hands around. The bit is just as hard and stiff as any other. You just have to be careful to let the bit do the work, and not manhandle it.
-
- Posts: 1346
- Joined: Tue Jan 10, 2012 4:55 pm
- Contact:
Re: Modifying the slot of a preform pipe stem - with video!
You sir have a manly voice.
- KurtHuhn
- Site Admin
- Posts: 5326
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: United States/Rhode Island
Re: Modifying the slot of a preform pipe stem - with video!
So I have been told.