Facing tool circles
Facing tool circles
I've gotten some relatively smooth stem faces, but most of the time my facing tool leaves little concentric circles on the face of the stock. I've tried different facing bit profiles and different angles of approach, as well as making sure my facing tool is centered. Is it possible this is a speed issue? I think 1200-1300rpms is the most I can coax out of my lathe. Thank you
Tim
Tim
- Tyler
- Site Supporter
- Posts: 2376
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: Farmersville, TX
- Contact:
Re: Facing tool circles
Bit profile and sharpness matters a lot, as does the speed you feed the tool. Also, you can take more than one pass to clean things up.
Tyler Lane Pipes
http://www.tylerlanepipes.com
http://www.tylerlanepipes.com
Re: Facing tool circles
I'll keep taking cracks at it. I've tried a bit I ground myself as well as a bit I bought. I've also gone multiple passes. What would you recommend for feed rate, fast or sloooow? Thanks Tyler
Re: Facing tool circles
I do at 1000rpm, and find that if I do the final pass and make it a very thin fine cut, it seems to leave a smoother surface. Also, the front angle need to be very close and only slightly off the line of the cut, I found.
I still sometime get the face looking as if the bit sort of burnt/scorched it. Maybe because the bit is not sharp enough??
I still sometime get the face looking as if the bit sort of burnt/scorched it. Maybe because the bit is not sharp enough??
Re: Facing tool circles
I'm still hand cutting my tennons on a wood lathe, but i have a ton of experience on a brake lathe. I'd say make your final cut thin and as slow a feed rate as you can. As long as your bits are sharp that should give you a nice finish.BeatusLiebowitz wrote:I'll keep taking cracks at it. I've tried a bit I ground myself as well as a bit I bought. I've also gone multiple passes. What would you recommend for feed rate, fast or sloooow? Thanks Tyler
I'd agreeCharl wrote: Also, the front angle need to be very close and only slightly off the line of the cut, I found.
I still sometime get the face looking as if the bit sort of burnt/scorched it. Maybe because the bit is not sharp enough??
Also, excessive vibration will also cause that.
- Tyler
- Site Supporter
- Posts: 2376
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: Farmersville, TX
- Contact:
Re: Facing tool circles
High rpm.
Slow feed.
Sharp tool.
Sharp tool.
Sharp tool.
And definitely the finishing pass should be a very light cut.
Of course, like Rad, my stem have tool marks on the face, so what do I know?
Slow feed.
Sharp tool.
Sharp tool.
Sharp tool.
And definitely the finishing pass should be a very light cut.
Of course, like Rad, my stem have tool marks on the face, so what do I know?
Tyler Lane Pipes
http://www.tylerlanepipes.com
http://www.tylerlanepipes.com
Re: Facing tool circles
I don't mind some tool marks, but these are pretty distinct and vinyl record-like. If, like Rad, you hoped this helped, it did. Thanks againTyler wrote:Of course, like Rad, my stem have tool marks on the face, so what do I know?
Re: Facing tool circles
I, too, have tool marks on the face of my stems. I'm not sure it should make that big of a difference like Rad says. I have three of Rad's pipes and could care less that the stem face isn't shiny and polished. I think trying to do so can be counterproductive. Everyone elses mileage may vary. If you come up with a quick and easy way to do it that doesn't booger up the stem fit please share.
Re: Facing tool circles
I touched the bit on the grinder, took much shallower cuts and slowed down my feed. It's already looking much better. Thanks again fellas!
Tim
Tim
Re: Facing tool circles
Try a skew chisel you pansy. Rock steady hands. Will. Determination. Man vs Nature. You get the picture.
ALL YOUR PIPE ARE BELONG TO US!
Re: Facing tool circles
What?!? Booooo! I love my compound tool holder and my home grindeded bits.Sasquatch wrote:Try a skew chisel you pansy. Rock steady hands. Will. Determination. Man vs Nature. You get the picture.