Rough edges on counter sink
-
- Posts: 8
- Joined: Thu Jan 16, 2014 11:51 pm
Rough edges on counter sink
A newbie here seeking advice on using the counter sink tool I just recently bought from Pimo. When I drill the counter sink bevel the edges are rough and a little uneven. My rpms on my drill press are set for the lowest, which 585 rpm. I wondered if I should set the press for a higher rpm? I did this with a pine block of wood to practice, the bevel seemed to be a little bit more smooth.
- sandahlpipe
- Posts: 2106
- Joined: Mon Feb 04, 2013 8:49 pm
- Location: Zimmerman, MN
- Contact:
Re: Rough edges on counter sink
I think I've seen them. At any rate, what you need to do is make sure the cutting edge of the countersink is sharp. If it's tearing wood, it's dull. If it's off-center, make sure your stummel doesn't move between drilling the mortise and drilling the countersink. It could also be that your countersink is off-center itself, but I think the other factors are more likely.
-
- Posts: 363
- Joined: Thu Feb 13, 2014 3:36 pm
- Location: Colorado Springs, Co
Re: Rough edges on counter sink
Recently while working with some zebra wood it kept tearing out just a little. I took my favorite file to my forstner bit. Now it just lightly shaves.
Sent from my banana phone.
Sent from my banana phone.
Re: Rough edges on counter sink
"Zero Flute" countersinks are the best for pipe making.
- DeflictedPipes
- Posts: 98
- Joined: Mon Feb 24, 2014 7:33 pm
- Location: Maryland
Re: Rough edges on counter sink
What size Zero Flute countersink would you need for a 5/16" mortice?
Mike
-
- Posts: 8
- Joined: Thu Jan 16, 2014 11:51 pm
Re: Rough edges on counter sink
I suppose that if a countersink bit is new it doesn't necessarily mean it's sharp. I 'll check that, but the edges do seem sharp.
- DeflictedPipes
- Posts: 98
- Joined: Mon Feb 24, 2014 7:33 pm
- Location: Maryland
Re: Rough edges on counter sink
Sorry to highjack the thread...DeflictedPipes wrote:What size Zero Flute countersink would you need for a 5/16" mortice?
Can anyone help me out with this? I'm getting ready to order my block drilling bits. Does anyone know if the the PIMO counterbore a good deal?
Mike
- sandahlpipe
- Posts: 2106
- Joined: Mon Feb 04, 2013 8:49 pm
- Location: Zimmerman, MN
- Contact:
Re: Rough edges on counter sink
DeflictedPipes,
The pimo tools will work ok for a hobbyist. I don't have any direct experience with their countersink. I think I got mine at a hardware store and it's about a half inch or so. Now I just use lathe tools to countersink since it's easier to get them sharp. You can also just use sandpaper if you're careful.
Sent from my iPhone using Tapatalk
The pimo tools will work ok for a hobbyist. I don't have any direct experience with their countersink. I think I got mine at a hardware store and it's about a half inch or so. Now I just use lathe tools to countersink since it's easier to get them sharp. You can also just use sandpaper if you're careful.
Sent from my iPhone using Tapatalk
Re: Rough edges on counter sink
Countersinks will be listed with a range of sizes that they cover, just choose one that covers 5/16". Lots of places sell them, you can even get them on ebay, they are sometimes called chatter free or chatterless countersinks. They work much better than standard countersinks for wood because of their sharp edge.
- DeflictedPipes
- Posts: 98
- Joined: Mon Feb 24, 2014 7:33 pm
- Location: Maryland
Re: Rough edges on counter sink
sandahlpipe wrote:The pimo tools will work ok for a hobbyist. I don't have any direct experience with their countersink. I think I got mine at a hardware store and it's about a half inch or so. Now I just use lathe tools to countersink since it's easier to get them sharp. You can also just use sandpaper if you're careful.
Thanks guys! Maybe my pipes won't be deflicted for too much longer.caskwith wrote:Countersinks will be listed with a range of sizes that they cover, just choose one that covers 5/16". Lots of places sell them, you can even get them on ebay, they are sometimes called chatter free or chatterless countersinks. They work much better than standard countersinks for wood because of their sharp edge.
Mike