Vermont Slot Funneling Tool - Help
Vermont Slot Funneling Tool - Help
Good afternoon guys!
Could any of you inform me of the blade diameter in Vermont Freehand's Slot Funneling Tool? I can only find the length but not the diameter.
Thank you very much.
Sweet Smokes
Bruno Robalo
Could any of you inform me of the blade diameter in Vermont Freehand's Slot Funneling Tool? I can only find the length but not the diameter.
Thank you very much.
Sweet Smokes
Bruno Robalo
- sandahlpipe
- Posts: 2106
- Joined: Mon Feb 04, 2013 8:49 pm
- Location: Zimmerman, MN
- Contact:
Re: Vermont Slot Funneling Tool - Help
It's the exact proper diameter for a slot.
Re: Vermont Slot Funneling Tool - Help
aka just around 2mm
Website: http://www.massispipes.com
Instagram : http://instagram.com/massispipes
Twitter: https://twitter.com/MassisPipes
Facebook: https://facebook.com/MassisPipes
Instagram : http://instagram.com/massispipes
Twitter: https://twitter.com/MassisPipes
Facebook: https://facebook.com/MassisPipes
Re: Vermont Slot Funneling Tool - Help
More like less than 1.5mm, I think. I use a 1.5mm bit for the funnel and the slot funneling tool of Steve fits comfortably and easily, without it being too tight.
Re: Vermont Slot Funneling Tool - Help
Went to check: I measure it as 1.25mm.
Re: Vermont Slot Funneling Tool - Help
Thank you for your answers!
I have found a store here in Portugal that sells these, with diameter starting in 0.5mm and going up to 3mm.
http://www.restaurarconservar.com/epage ... File-10%22
What do you guys think of these? The pattern on the file is a lot different than Steve's. Maybe it won't remove material so quickly but it can leave a smoother finish from it's use.
They are a bit pricey but i think i will try one considering that when ordering from the USA i have to pay for the high salaries of the customs officers
I have found a store here in Portugal that sells these, with diameter starting in 0.5mm and going up to 3mm.
http://www.restaurarconservar.com/epage ... File-10%22
What do you guys think of these? The pattern on the file is a lot different than Steve's. Maybe it won't remove material so quickly but it can leave a smoother finish from it's use.
They are a bit pricey but i think i will try one considering that when ordering from the USA i have to pay for the high salaries of the customs officers
Re: Vermont Slot Funneling Tool - Help
If I remember right, cut 3 is very fine. If that is all that's available, I would leave it.
That is, if you're idea is too use it for cutting the slot.
A modified saw blade would do a better job.
That is, if you're idea is too use it for cutting the slot.
A modified saw blade would do a better job.
Re: Vermont Slot Funneling Tool - Help
That's strange, I've got 3 of them from Steve and none of them fit into a 1.5mm hole as far as I recall. I'll verify that when I get back home though...Charl wrote:Went to check: I measure it as 1.25mm.
Website: http://www.massispipes.com
Instagram : http://instagram.com/massispipes
Twitter: https://twitter.com/MassisPipes
Facebook: https://facebook.com/MassisPipes
Instagram : http://instagram.com/massispipes
Twitter: https://twitter.com/MassisPipes
Facebook: https://facebook.com/MassisPipes
- oklahoma red
- Posts: 1084
- Joined: Tue Apr 12, 2011 6:14 pm
Re: Vermont Slot Funneling Tool - Help
In my next attempt to be useful I'll try to present the following in such a manner that even Tyler and George can follow along
Info on slot funneling tool as sold by Vermont Freehand.
Actual manufacturer/model: Kemper Tools/K-31 (Kemper is the maker of an extensive line of tools for working with ceramics). Their description: Zig-Zag saw.
I have two and they both measure .050 in diameter (1.28mm).
They also offer a model K-32 described as a heavy duty model but no diameter is given in their catalog. There is a visual difference in diameter between the two as shown in their picture.
I would guess that it is too big or Steve would be offering it. Call Kemper if you really want to know.
Info on slot funneling tool as sold by Vermont Freehand.
Actual manufacturer/model: Kemper Tools/K-31 (Kemper is the maker of an extensive line of tools for working with ceramics). Their description: Zig-Zag saw.
I have two and they both measure .050 in diameter (1.28mm).
They also offer a model K-32 described as a heavy duty model but no diameter is given in their catalog. There is a visual difference in diameter between the two as shown in their picture.
I would guess that it is too big or Steve would be offering it. Call Kemper if you really want to know.
-
- Posts: 3120
- Joined: Sun Sep 02, 2007 4:29 am
- Location: Kansas City, USA
- Contact:
Re: Vermont Slot Funneling Tool - Help
Or, you could just cut some lengths of Delrin rod to handle length, drill a 1" deep axial hole that's slightly smaller in diameter than the OD of the blade, and screw these it in:
http://www.ottofrei.com/Store/Saw-Blade ... 5-890.html
Wrap the handle with a bit-O-coach's or stage tape for a comfy, secure grip, and you're home.
http://www.ottofrei.com/Store/Saw-Blade ... 5-890.html
Wrap the handle with a bit-O-coach's or stage tape for a comfy, secure grip, and you're home.
UFOs must be real. There's no other explanation for cats.
- oklahoma red
- Posts: 1084
- Joined: Tue Apr 12, 2011 6:14 pm
Re: Vermont Slot Funneling Tool - Help
Delrin? Axial? OD? I'm sorry, I don't understand. Please explain before I stun an elephant.LatakiaLover wrote:Or, you could just cut some lengths of Delrin rod to handle length, drill a 1" deep axial hole that's slightly smaller in diameter than the OD of the blade, and screw these it in:
http://www.ottofrei.com/Store/Saw-Blade ... 5-890.html
Wrap the handle with a bit-O-coach's or stage tape for a comfy, secure grip, and you're home.
-
- Posts: 3120
- Joined: Sun Sep 02, 2007 4:29 am
- Location: Kansas City, USA
- Contact:
Re: Vermont Slot Funneling Tool - Help
My apologies, Red, I forgot you're from the north side of the Red River.oklahoma red wrote: Delrin? Axial? OD? I'm sorry, I don't understand. Please explain before I stun an elephant.
Delrin is fancy plastic that's cheap and comes in long cylindrical pieces called rods. Gotta getcha summa that.
Then lop it into 2" chunks with a saw.
Then take each piece a-that and drill a inch deep hole in the end of it, rat down the middle usin' wunna them twisty drill bit things. Choose ya one that's a coupla hunnerts smaller across than the spiral saw blade, then screw it in the hole---it'll self tap cuz it's sharp---and it'll stay put reel good.
Fine-ly, since Delrin is slippery stuff, wrap the handle with a few inches of some sort of cloth tape so's it's easier to grab.
Or, you could forget alla that crap and make yerself a jig that cuts perfect slots every time in a few seconds. That would probably be beyond ya, though.
UFOs must be real. There's no other explanation for cats.
- PremalChheda
- Posts: 1213
- Joined: Sat Dec 11, 2010 6:03 pm
- Location: Columbus, Ohio, USA
- Contact:
Re: Vermont Slot Funneling Tool - Help
It is approximately 3/64".brurobas wrote:Good afternoon guys!
Could any of you inform me of the blade diameter in Vermont Freehand's Slot Funneling Tool? I can only find the length but not the diameter.
Thank you very much.
Sweet Smokes
Bruno Robalo
Premal Chheda
http://www.chhedapipes.com - Just for fun
http://www.smokershaven.com - New & Estate Pipes
http://www.rawkrafted.com - Pipe Making Tools, Materials, & Supplies
http://www.chhedapipes.com - Just for fun
http://www.smokershaven.com - New & Estate Pipes
http://www.rawkrafted.com - Pipe Making Tools, Materials, & Supplies
- oklahoma red
- Posts: 1084
- Joined: Tue Apr 12, 2011 6:14 pm
Re: Vermont Slot Funneling Tool - Help
OMG!! My head is spinning! So much to absorb. I see elephants and they are pink!LatakiaLover wrote:My apologies, Red, I forgot you're from the north side of the Red River.oklahoma red wrote: Delrin? Axial? OD? I'm sorry, I don't understand. Please explain before I stun an elephant.
Delrin is fancy plastic that's cheap and comes in long cylindrical pieces called rods. Gotta getcha summa that.
Then lop it into 2" chunks with a saw.
Then take each piece a-that and drill a inch deep hole in the end of it, rat down the middle usin' wunna them twisty drill bit things. Choose ya one that's a coupla hunnerts smaller across than the spiral saw blade, then screw it in the hole---it'll self tap cuz it's sharp---and it'll stay put reel good.
Fine-ly, since Delrin is slippery stuff, wrap the handle with a few inches of some sort of cloth tape so's it's easier to grab.
Or, you could forget alla that crap and make yerself a jig that cuts perfect slots every time in a few seconds. That would probably be beyond ya, though.
-
- Posts: 3120
- Joined: Sun Sep 02, 2007 4:29 am
- Location: Kansas City, USA
- Contact:
Re: Vermont Slot Funneling Tool - Help
Actually, it would be a good time to post a few pics of your home-brewed slot machine. (get it? slot machine )
UFOs must be real. There's no other explanation for cats.
- Tyler
- Site Supporter
- Posts: 2376
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: Farmersville, TX
- Contact:
Re: Vermont Slot Funneling Tool - Help
Much better!oklahoma red wrote:In my next attempt to be useful I'll try to present the following in such a manner that even Tyler and George can follow along
Info on slot funneling tool as sold by Vermont Freehand.
Actual manufacturer/model: Kemper Tools/K-31 (Kemper is the maker of an extensive line of tools for working with ceramics). Their description: Zig-Zag saw.
I have two and they both measure .050 in diameter (1.28mm).
They also offer a model K-32 described as a heavy duty model but no diameter is given in their catalog. There is a visual difference in diameter between the two as shown in their picture.
I would guess that it is too big or Steve would be offering it. Call Kemper if you really want to know.
In other news, I wasn't just picking on you. The whole thread was a obfuscation masterpiece.
Tyler Lane Pipes
http://www.tylerlanepipes.com
http://www.tylerlanepipes.com
Re: Vermont Slot Funneling Tool - Help
He's that guy who said, "Man who lose key to girl's apartment get no new key."Charl wrote:Who's Confucius?
Ryan Richardson
R2 Pipes/Ryan's Luxury Goods
______________________________________
"You can't convince a stupid person that what he's doing is stupid, because the stupidness inside him is telling him that it's smart"
R2 Pipes/Ryan's Luxury Goods
______________________________________
"You can't convince a stupid person that what he's doing is stupid, because the stupidness inside him is telling him that it's smart"
- seamonster
- Posts: 380
- Joined: Fri Feb 21, 2014 12:43 am
- Location: Portland, OR
Re: Vermont Slot Funneling Tool - Help
and the guy who said, "Man who stick head in punch bowl get punch in nose."Ratimus wrote:He's that guy who said, "Man who lose key to girl's apartment get no new key."Charl wrote:Who's Confucius?
sent from my blah-dee-blah, using hooty-hoo
instagram.com/seamonster_workshop/