pipemakersforum.com

This a pipe I made with morta. The shank extension is acrylic and it has a military mount juma stem. I can't sandblast so it was left smoov. While it was fun to make a pipe out of morta, briar is still preferred. I had made another pipe out of morta that never made it up for reviews and was smoked by yours truely. It cracked on the rim during the first smoke from heat I'm assuming. Anyhow, I will leave morta to the guys that understand it better than I do.

Critiques and comments are welcome








Thanks for looking,
Kiel

Overall, not so bad. (that means good)

More space/material in the curve of the flare on the mortise side of the pipe, and centering the high point by adjust both the flare and saddle. A little shorter on the stem may be more attractive as well.

Very attractive pipe. If I were a morta fan, I would want that pipe in my rotation!
What are the attractions of juma? I see it popping up more frequently on the artisan pipes. I like the look and feel of acrylic, but find it harder to work than ebonite, and have no experience with juma.
DocAitch.

PremalChheda wrote:Overall, not so bad. (that means good)

More space/material in the curve of the flare on the mortise side of the pipe, and centering the high point by adjust both the flare and saddle. A little shorter on the stem may be more attractive as well.

Thank you Premal. When I am doing the curve on a saddle stem I have some chainsaw files and a few dowel rods with different diameters. I always find that the saddle gets sanded too much and changes the shape of the whole stem, or not enough and looks like it does now. Now I pretty sure the answer is just to take more time and be more careful while making the saddle, but I am also open to suggestions on better methods or more useful tools.

DocAitch wrote:Very attractive pipe. If I were a morta fan, I would want that pipe in my rotation!
What are the attractions of juma? I see it popping up more frequently on the artisan pipes. I like the look and feel of acrylic, but find it harder to work than ebonite, and have no experience with juma.
DocAitch.

Thanks Doc. I am going to put this pipe into my rotation and hopefully it goes better than the first morta that cracked on me.

Last summer when I was travelling around America, a good friend of mine gave me a rod of juma because he isn't using it as often as he thought he would. I really enjoy working with juma. I feel it is easier to work with than acrylic and ebonite. 　Ｉ　ｕｓｅｄ　ｉｔ　
ｏｎ　ａ　ｂｅｎｔ　ｐｉｐｅ　Ｉ　ｍａｄｅ　ｆｏｒ　ｍｙｓｅｌｆ　ａ　ｃｏｕｐｌｅ　ｍｏｎｔｈｓ　ａｇｏ，　ａｎｄ　ｎｏｔｉｃｅｄ　
ｔｈａｔ　ｔｈｅ　ｓｔｅｍ　ｉｓ　ｓｌｏｗｌｙ　ｌｏｓｉｎｇ　ｉｔ＇ｓ　ｂｅｎｄ．　　Ｎｏｔ　ｓｕｒｅ　ｉｆ　ｔｈａｔ　ｉｓ　ｎｏｒｍａｌ　ｗｉｔｈ　ｊｕｍａ，　ｂｕｔ　ｗｅ＇ｌｌ　ｈａｖｅ　ｔｏ　ｗａｉｔ　ｔｏ　ｓｅｅ　ｗｈａｔ　ｏｔｈｅｒ　ｐｅｏｐｌｅ　ｓａｙ　ａｂｏｕｔ　ｉｔ．　　Ｓｏｒｒｙ　ａｂｏｕｔ　ｔｈｅ　ｓｕｄｄｅｎ　ｃｈａｎｇｅ　ｉｎ　ｔｈｅ　ｆｏｎｔ．　　Ｉ　ａｍ　ｕｓｉｎｇ　ｍｙ　
ｗｉｆｅ＇ｓ　ｃｏｍｐｕｔｅｒ　ａｎｄ　ｉｔ　ｃａｎ　ｓｕｄｄｅｎｌｙ　ｂｅｃｏｍｅ　ｓｔｕｐｉｄ．