My idea is to preserve as much plateau as possible.

davidpiepkorn1 · Post by **davidpiepkorn1** » Sat Feb 15, 2020 12:20 am

Sent from my iPhone using Tapatalk

Adui · Post by **Adui** » Sat Feb 15, 2020 12:44 am

I'll be interested to see it progress. I've never worked a Plateux block.

davidpiepkorn1 · Post by **davidpiepkorn1** » Sat Feb 22, 2020 10:45 pm

This really is hard. Difficult and imaginatively challenging.

Sent from my iPhone using Tapatalk

davidpiepkorn1 · Post by **davidpiepkorn1** » Sun Feb 23, 2020 12:52 am

Sent from my iPhone using Tapatalk

DocAitch · Post by **DocAitch** » Sun Feb 23, 2020 1:05 am

Think about your premise and look at what is being produced by the experienced pipe makers out there.
With rare exceptions, plateau is left on the finished pipe only when it is part of the design. Volcanos, horns, and more standard shapes with plateau tops all work.
Think about making a smoking device that incorporates the plateau in an integrated design, rather than a sculpture that maximizes plateau.
DocAitch

davidpiepkorn1 · Post by **davidpiepkorn1** » Sun Feb 23, 2020 1:17 am

“Think about making a smoking device that incorporates the plateau in an integrated design, rather than a sculpture that maximizes plateau.”

... thoughtful thoughts, that’s why I’m here and so glad I am.

Thank you for sharing your wisdom, I will certainly take it into deep consideration.

Sent from my iPhone using Tapatalk

davidpiepkorn1 · Post by **davidpiepkorn1** » Sun Mar 01, 2020 1:05 am

I really really want to make the plateau the focus of the pipe’s form. I believe, from some years of experience, that good smokers are a product of decent drilling and an agreeable tobac. Perhaps a sculpture featuring plateau is what I shall pursue, not disregarding advice to the contrary, rather taking it into account upon smoking the beast thereafter and considering its suitability as a smoking instrument.

Sent from my iPhone using Tapatalk

wdteipen · Post by **wdteipen** » Sun Mar 01, 2020 9:34 am

There's one way to find out if your idea works or not. Do it! And have fun. And post the results and we can discuss your design.

davidpiepkorn1 · Post by **davidpiepkorn1** » Sat Mar 07, 2020 9:26 pm

Sent from my iPhone using Tapatalk

davidpiepkorn1 · Post by **davidpiepkorn1** » Sat Mar 21, 2020 11:46 pm

Sent from my iPhone using Tapatalk

davidpiepkorn1 · Post by **davidpiepkorn1** » Sat Mar 21, 2020 11:46 pm

Sent from my iPhone using Tapatalk

davidpiepkorn1 · Post by **davidpiepkorn1** » Sat Mar 21, 2020 11:47 pm

Sent from my iPhone using Tapatalk

UnderShade · Post by **UnderShade** » Sun Mar 22, 2020 1:54 am

I’m trying to get an idea of what you’re going for by looking at your sketching, but I’m not seeing it. What would you say your overall goal is? Are you wanting to have a block (displaying the plateaux) with a stem that is smokable? Are you going for any particular shape? What kind of tooling are you working with? Sorry for all the questions, but I really want to get a better understanding of the intended end-result for this pipe before making any suggestions or offering my opinion.

davidpiepkorn1 · Post by **davidpiepkorn1** » Fri Mar 27, 2020 1:36 am

UnderShade wrote:I’m trying to get an idea of what you’re going for by looking at your sketching, but I’m not seeing it. What would you say your overall goal is? Are you wanting to have a block (displaying the plateaux) with a stem that is smokable? Are you going for any particular shape? What kind of tooling are you working with? Sorry for all the questions, but I really want to get a better understanding of the intended end-result for this pipe before making any suggestions or offering my opinion.

UnderShade, I’m shaving and picking along as I go. I now understand this group is concerned primarily with plans and how close one can come to meeting those requirements. I will refrain from posting photos of the progress, and finally show a pic or two of the finished product for analysis, (God knows how far out that date may be). This won’t allow artists to judge how close I’ve come to my original concept, but, any feedback will
open to me new avenues of evaluation.

Sent from my iPhone using Tapatalk

davidpiepkorn1 · Post by **davidpiepkorn1** » Sun May 17, 2020 1:11 am

So far.

I’ve afforded myself the luxury of a rotary tool this time. I love the ability now to visualize shape and realize it in time before I lose the idea and mess it up a few weeks/months later.

Sent from my iPhone using Tapatalk

seamonster · Post by **seamonster** » Mon May 18, 2020 4:28 pm

Okay, you're starting to develop a language, here. Ala Henry Moore. Now the truck is to make the whole block speak the same dialect. That square 'window' on the top is decidedly speaking Greek....

Sent from my bloopty-bloop, using hooty-hoo.

davidpiepkorn1 · Post by **davidpiepkorn1** » Mon May 18, 2020 4:44 pm

seamonster wrote:Okay, you're starting to develop a language, here. Ala Henry Moore. Now the truck is to make the whole block speak the same dialect. That square 'window' on the top is decidedly speaking Greek....

Sent from my bloopty-bloop, using hooty-hoo.

Yes, the square will not remain a square, it is starting point and that entire structure may go completely away if it refuses to flow.

Sent from my iPhone using Tapatalk

davidpiepkorn1 · Post by **davidpiepkorn1** » Sat May 23, 2020 8:13 pm

I like the analogy of developing “a language”. Thank you. I will show as it evolves.

Sent from my iPhone using Tapatalk

davidpiepkorn1 · Post by **davidpiepkorn1** » Sat Jun 13, 2020 5:40 pm

davidpiepkorn1 wrote:I like the analogy of developing “a language”. Thank you. I will show as it evolves.

Sent from my iPhone using Tapatalk

Oops I did it again. No sand pit this time.

Sent from my iPhone using Tapatalk

pipemakersforum.com