Making bamboo shanks
Making bamboo shanks
Started playing w/bamboo today. Have to say, a different animal! For those 'in the know', I'd sure like to know how to do this. I've searched and read what I could, and have approached it with the tools I have and outlined it below. If I'm off track or if there's a better way I'd sure like to hear it.
Drilled 2 blocks. On one block, after drilling the air hole, I put a 3/16 mortise in it for the tube. On the second block, I drilled a 5/16 mortise, then put in a piece of 5/16 delrin that has the 3/16 mortise in it for the tube.
Now onto the bamboo. Made 2, 2 knuckle stems. BTW - Doing all this on a Delta Midi lathe....
I wanted the bamboo ends at the center of the knuckles. I cut a couple pieces that were about 3 knuckles long.
I chucked one piece in the lathe and had to keep adjusting it's position in the (#1 Spigot) jaws in order to get it as centered as I could.
I used a 9/64 tapered bit and drilled a little over half way through the piece. Then a forstner bit to square the end, then a 3/16 mortise. Flipped the piece around and had to fidget with the centering before doing the same to that end.
That's where I left it for the day. Now I have to figure out the stem/tube relationship/process.
Drilled 2 blocks. On one block, after drilling the air hole, I put a 3/16 mortise in it for the tube. On the second block, I drilled a 5/16 mortise, then put in a piece of 5/16 delrin that has the 3/16 mortise in it for the tube.
Now onto the bamboo. Made 2, 2 knuckle stems. BTW - Doing all this on a Delta Midi lathe....
I wanted the bamboo ends at the center of the knuckles. I cut a couple pieces that were about 3 knuckles long.
I chucked one piece in the lathe and had to keep adjusting it's position in the (#1 Spigot) jaws in order to get it as centered as I could.
I used a 9/64 tapered bit and drilled a little over half way through the piece. Then a forstner bit to square the end, then a 3/16 mortise. Flipped the piece around and had to fidget with the centering before doing the same to that end.
That's where I left it for the day. Now I have to figure out the stem/tube relationship/process.
It's needlessly difficult trying to chuck bamboo. Try this:
Most bamboo has a tiny hole in the center of the cross-section, use this as a center. If the piece appears solid, use a punch to make a dimple in the center. This is best done by eye, as bamboo is usually too irregular to measure.
Don't worry about squaring the ends for now. Chuck a tapered drill in the headstock, and use a center in the tailstock, located in the hole or dimple of one end, to guide the bamboo onto the spinning drill bit as you hold it by hand. Do a little, switch ends, and repeat. Allow the bamboo to rotate a quarter turn or so every little while so you can judge your progress in keeping it in line. Pretty soon the holes will meet, and you can push through. I usually start with a 1/8" tapered bit and enlarge to 3/16", seems to wind up a little cleaner. This is your best chance of getting a hole right through from point to point.
At this point, I use an aircraft counterbore with a 3/16" pilot to square the ends. I got a counterbore with at 3/16" bore so a piece of 3/16" drill blank that protrudes about an inch can be used as a pilot, this keeps it square better than the little stub pilots you get if you buy one. If I'm trying to merely square the ends and not actually remove much material, I just insert the counterbore and turn by hand. Bamboo end grain shaves very easily and evenly.
Alternately, as has been covered in other threads, you can use a piece of rod as a mandrel and square the ends turning the mandrel in the lathe.
To repeat, though, you'll have so much trouble consistently centering and squaring a piece of bamboo in a chuck that it's hardly worth the trouble. The method above takes minutes.
Most bamboo has a tiny hole in the center of the cross-section, use this as a center. If the piece appears solid, use a punch to make a dimple in the center. This is best done by eye, as bamboo is usually too irregular to measure.
Don't worry about squaring the ends for now. Chuck a tapered drill in the headstock, and use a center in the tailstock, located in the hole or dimple of one end, to guide the bamboo onto the spinning drill bit as you hold it by hand. Do a little, switch ends, and repeat. Allow the bamboo to rotate a quarter turn or so every little while so you can judge your progress in keeping it in line. Pretty soon the holes will meet, and you can push through. I usually start with a 1/8" tapered bit and enlarge to 3/16", seems to wind up a little cleaner. This is your best chance of getting a hole right through from point to point.
At this point, I use an aircraft counterbore with a 3/16" pilot to square the ends. I got a counterbore with at 3/16" bore so a piece of 3/16" drill blank that protrudes about an inch can be used as a pilot, this keeps it square better than the little stub pilots you get if you buy one. If I'm trying to merely square the ends and not actually remove much material, I just insert the counterbore and turn by hand. Bamboo end grain shaves very easily and evenly.
Alternately, as has been covered in other threads, you can use a piece of rod as a mandrel and square the ends turning the mandrel in the lathe.
To repeat, though, you'll have so much trouble consistently centering and squaring a piece of bamboo in a chuck that it's hardly worth the trouble. The method above takes minutes.
- KurtHuhn
- Site Admin
- Posts: 5326
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: United States/Rhode Island
Jack's method is nearly identical to mine.
The only thing I could possibly add to Jack's exhaustive set of directions, is that, when drilling bamboo, you aim for a larger than normal airway size. Jack mentioned 3/16" - which is the same I use. The reason is that the bamboo fibers have a tendency to swell slightly when exposed to moisture (as in pipe smoke) so you want to compensate for that.
The only thing I could possibly add to Jack's exhaustive set of directions, is that, when drilling bamboo, you aim for a larger than normal airway size. Jack mentioned 3/16" - which is the same I use. The reason is that the bamboo fibers have a tendency to swell slightly when exposed to moisture (as in pipe smoke) so you want to compensate for that.
- KurtHuhn
- Site Admin
- Posts: 5326
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: United States/Rhode Island
Interestingly, steaming bamboo will actually harm it. Due to the hollow nature of bamboo, the areas between the knuckles can collapse if steamed and bent or straightened. If you want to straighten bamboo, you can leave it dry and try to force it straight by strapping it to a board or something.
However, I normally incorporate gently curved pieces into the shape of a pipe. You have to adjust your drilling to compensate, but it isn't appreciably more difficult.
However, I normally incorporate gently curved pieces into the shape of a pipe. You have to adjust your drilling to compensate, but it isn't appreciably more difficult.
As an experiment I tried soaking & bending a piece of bamboo. It bent OK, but as Kurt mentioned, it tends to flatten a bit between knuckles at the bend, plus the hard outer layer doesn't compress on the inner curve. It tends to wrinkle up making tiny corrugations in the "skin".KurtHuhn wrote:Due to the hollow nature of bamboo, the areas between the knuckles can collapse if steamed and bent or straightened.
I was wondering if a narrow diameter pipe bender might work. Since I don't have one, it remains to be seen.
Regards,
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett
- KurtHuhn
- Site Admin
- Posts: 5326
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: United States/Rhode Island
If you want to bend bamboo, the best method is actually *heat*. I've bent a few bamboo shanks using a propane torch and a waste block cut with the radius I want. You might be able to better control the heat by using an oven, but I haven't tried that.
The same method will work for rattan and bamboo stalks.
However, as I recently told a customer, putting a tight bend in a bamboo shank/stem pretty much prevents ever being able to ream it out with a drill bit in the future, which is why I've never sold a pipe with a bent bamboo shank.
The same method will work for rattan and bamboo stalks.
However, as I recently told a customer, putting a tight bend in a bamboo shank/stem pretty much prevents ever being able to ream it out with a drill bit in the future, which is why I've never sold a pipe with a bent bamboo shank.
So it stands to reason that if you can introduce a bend in a piece of bamboo, you *should* be able to straighten out a piece that has a slight bend...using heat, or if it hasn't been drilled yet, maybe even steam to soften the fiber.KurtHuhn wrote:If you want to bend bamboo, the best method is actually *heat*. I've bent a few bamboo shanks using a propane torch and a waste block cut with the radius I want. You might be able to better control the heat by using an oven, but I haven't tried that.
- KurtHuhn
- Site Admin
- Posts: 5326
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: United States/Rhode Island
I suggest never steaming - not unless you really want to risk destroying a perfectly good piece of bamboo.
Some bamboo can be temporarily straightened for drilling just by strapping/clamping it to something straight - like a board or dowel. Severely bent bamboo should, perhaps, be discarded. However, if you really want to make a bent piece of bamboo straight, use heat. I've only ever seen or used a propane torch, but you *might* be able to use an oven. I don't know. It seemed to me that localized heat worked better.
Some bamboo can be temporarily straightened for drilling just by strapping/clamping it to something straight - like a board or dowel. Severely bent bamboo should, perhaps, be discarded. However, if you really want to make a bent piece of bamboo straight, use heat. I've only ever seen or used a propane torch, but you *might* be able to use an oven. I don't know. It seemed to me that localized heat worked better.
You can give it a light sanding with very fine sandpaper, but that's not really necessary because of the hard outer "skin". It buffs to a beautiful shine and doesn't need anything other than a final coat of carnauba.Smitty wrote:I was wondering if the bamboo needs any care once finished. Does it need a protective coating of anything on it, or is it good to go as is?
Regards,
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett
Got a C-bore tool w/a 3/16 pilot and a drill rod blank. Figured out where to cut the drill rod in order to get about a 1" pilot extension from the cbore tool. Chucked up the drill rod on a motor and took my dremel w/a cut-off disc and cut the rod to the length I wanted.JHowell wrote: At this point, I use an aircraft counterbore with a 3/16" pilot to square the ends. I got a counterbore with at 3/16" bore so a piece of 3/16" drill blank that protrudes about an inch
Put the rod in the c-bore tool and put it in the chuck on my motor and tested it on some bamboo I had drilled. SWEEEEEEET !!!!
THANK YOU!