So I had a couple cheap unfinished pipes given to me. Both are briar and I believe at least an attempt at a billiard. The drilling seems consistent with what I am learning is that style, though I think its a bit too far off 90 degrees. Both pipes came carved to a point that the bowl was oval, with nearly twice as much material in the front and back as in either side. I reshaped this one, and it is currently sanded to 500 grit. The briar had a defect in the front of the bowl, but I think its still serviceable. Reshaping done with rasps files a dremel and lots of sanding with a palm sander.
With the caveat that I didn't make the stem, only cleaned it up, and didn't drill the thing. Whats wrong with it? Also, what did I get right, (if anything)? Also suggestions for better photos. I couldn't get the camera to focus on my desk so this is the kitchen counter.
No money shot because its not finished
Practice carve
Practice carve
I hope to be at least half the person my dogs thinks I am.
AKA Terry
AKA Terry
Re: Practice carve
DocAitch
"Hettinger, if you stamp 'hand made' on a dog turd, some one will buy it."
-Charles Hollyday, pipe maker, reluctant mentor, and curmudgeon
" Never show an idiot an unfinished pipe!"- same guy
-Charles Hollyday, pipe maker, reluctant mentor, and curmudgeon
" Never show an idiot an unfinished pipe!"- same guy
Re: Practice carve
I find it helpful to dissect the shape into component geometrical shapes.
DocAitch
"Hettinger, if you stamp 'hand made' on a dog turd, some one will buy it."
-Charles Hollyday, pipe maker, reluctant mentor, and curmudgeon
" Never show an idiot an unfinished pipe!"- same guy
-Charles Hollyday, pipe maker, reluctant mentor, and curmudgeon
" Never show an idiot an unfinished pipe!"- same guy
Re: Practice carve
Wow. Thank you both for the diagrams! this is most helpful! I'll make the adjustments and re-sand before moving to the next phase on this one!
I hope to be at least half the person my dogs thinks I am.
AKA Terry
AKA Terry
Re: Practice carve
Update before bed: Adjustments made per your diagrams. It's not perfect, but I think I got close. My guess is I still need to remove some material at the base of the bowl to shank union
I hope to be at least half the person my dogs thinks I am.
AKA Terry
AKA Terry
Re: Practice carve
Better, but as you note, still has to be tightened up a bit.
Take a piece of card stock or other straight edge to your shank to check the lines. Your line appears to pinch in at the stem/shank junction on the top side view. This is a job for a large flat file or possibly a nail emery board,
You will produce a cylindrical polygon that tapers very slightly. When your file cuts are parallel and even, round off with sandpaper.
It also helps to rotate the stem 180 degrees, then 90, then 45 every few cuts to maintain roundness. Cut EITHER the wood or the ebonite, depending on which is higher.
DocAitch
Take a piece of card stock or other straight edge to your shank to check the lines. Your line appears to pinch in at the stem/shank junction on the top side view. This is a job for a large flat file or possibly a nail emery board,
You will produce a cylindrical polygon that tapers very slightly. When your file cuts are parallel and even, round off with sandpaper.
It also helps to rotate the stem 180 degrees, then 90, then 45 every few cuts to maintain roundness. Cut EITHER the wood or the ebonite, depending on which is higher.
DocAitch
"Hettinger, if you stamp 'hand made' on a dog turd, some one will buy it."
-Charles Hollyday, pipe maker, reluctant mentor, and curmudgeon
" Never show an idiot an unfinished pipe!"- same guy
-Charles Hollyday, pipe maker, reluctant mentor, and curmudgeon
" Never show an idiot an unfinished pipe!"- same guy
Re: Practice carve
Two more tips:
I use a compass to get the top of the bowl right. That is a piece of dowel turned to size of chamber with a lip for centering the compass
This is a photo to illustrate my comment about the polygon and using the file cuts to guide the trueness of your cylinder and its taper.
DocAitch
I use a compass to get the top of the bowl right. That is a piece of dowel turned to size of chamber with a lip for centering the compass
This is a photo to illustrate my comment about the polygon and using the file cuts to guide the trueness of your cylinder and its taper.
DocAitch
"Hettinger, if you stamp 'hand made' on a dog turd, some one will buy it."
-Charles Hollyday, pipe maker, reluctant mentor, and curmudgeon
" Never show an idiot an unfinished pipe!"- same guy
-Charles Hollyday, pipe maker, reluctant mentor, and curmudgeon
" Never show an idiot an unfinished pipe!"- same guy
Re: Practice carve
So I decided that this one should be finished as is, its a small pipe and there's not a lot of material left to remove. I know it isn't perfect, but I don't want to sand too much off so I'm going with this for this pipe. That said, tell me the good bad and ugly on it, so I can get the next one better.
The bowl is approximately an inch across, the overall length is about 5 1/2 inches.
I made an attempt to do a contrast staining.
The bowl is approximately an inch across, the overall length is about 5 1/2 inches.
I made an attempt to do a contrast staining.
I hope to be at least half the person my dogs thinks I am.
AKA Terry
AKA Terry
Re: Practice carve
I just reread what doc posted. I see it now! Should have done more work there, the stem s still looks pinched at the union
I hope to be at least half the person my dogs thinks I am.
AKA Terry
AKA Terry
Re: Practice carve
I just noticed I didnt give a topside view of the finished pipe.Disclaimer, there is no stain in the chamber, its just very dark briar.
I hope to be at least half the person my dogs thinks I am.
AKA Terry
AKA Terry