suggestions for putting name on pipe...

Sanding, rusticating, sandblasting, buffing, etc. All here.
Post Reply
Patrick
Posts: 62
Joined: Mon Oct 27, 2008 12:21 pm
Location: Texas

suggestions for putting name on pipe...

Post by Patrick »

Other than using a steel stamp to put name on pipe, what other ways are there for permanent marking? Thanks!
User avatar
Frank
Posts: 1341
Joined: Thu Nov 23, 2006 8:00 pm
Location: Southern California

Post by Frank »

It depends on what you can afford. There's laser etching and mechanical etching. If you have a steady hand, a Dremel and small bit....
Regards,
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett
Patrick
Posts: 62
Joined: Mon Oct 27, 2008 12:21 pm
Location: Texas

Post by Patrick »

In the past I have tried Dremel but it does not look good. Tell me more about the others and how do I go about it. I could buy a steel stamp name but they want $75.00. Thanks, Patrick
User avatar
flix
Posts: 522
Joined: Thu Nov 23, 2006 8:00 pm

Post by flix »

Before I purchased the stamp, I used a soldering iron with a fine point tip. Lot's of practice is needed to keep the marking look decent. I do believe that a wood burning kit should work well, assuming a fine enough tip. HTH...
User avatar
Frank
Posts: 1341
Joined: Thu Nov 23, 2006 8:00 pm
Location: Southern California

Post by Frank »

Actually, my above post should have read mechanical engraving not etching. If $75 is too steep for a stamp, then don't even consider laser. A mechanical engraver works slightly different from a Dremel, but you still need a good eye and a steady hand. The setup would still cost more than a steel stamp.

As flix mentioned, the cheapest way to go would be a fine point soldering iron, but again, good eye... steady hand... yadda, yadda.
Regards,
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett
User avatar
KurtHuhn
Site Admin
Posts: 5326
Joined: Thu Nov 23, 2006 8:00 pm
Location: United States/Rhode Island

Post by KurtHuhn »

A steel stamp is actually the least expensive way to get good, repeatable impressions of your logo, name, and whatever else you want on the pipe.

If you're planning on selling your pipes, a stamp is pretty much required unless you're going to go the way of Eltang and Geiger and use a pantograph engraver. Every once in a while I'll run into pipes that I sold before I had a stamp, and the dremel scrawling makes me cringe to no end.
Kurt Huhn
AKA: Oversized Ostrogoth
artisan@k-huhn.com
User avatar
alan
Posts: 121
Joined: Sat Aug 16, 2008 8:35 pm
Location: Michigan

Post by alan »

Any recommendations on where to get the stamp made? I've looked for individual letter stamps to just do initials at every craft shop my wife has dragged me to, and I find nothing. A custom logo stamp would be much better than basic letters.
User avatar
Tsunami
Posts: 174
Joined: Sun Apr 20, 2008 7:38 pm
Location: Connecticut
Contact:

Post by Tsunami »

I use a Pantograph Engraver on my stummels and cut the logo in my stems. The reason is two fold.
1. It is deep in the wood 10-15 thousandth deep.
2. I used to be an engraver and I still have easy access to the equipment when needed.
User avatar
KurtHuhn
Site Admin
Posts: 5326
Joined: Thu Nov 23, 2006 8:00 pm
Location: United States/Rhode Island

Post by KurtHuhn »

alan wrote:Any recommendations on where to get the stamp made? I've looked for individual letter stamps to just do initials at every craft shop my wife has dragged me to, and I find nothing. A custom logo stamp would be much better than basic letters.
Paul at A&M Steel Stamps:
A & M Steel Stamps
55 Windsor Ave,
Mineola, N.Y. 11501
Phone: 516-741-6223
E-mail: mailto:amsteelstamps@yahoo.com

Tell him Kurt sent you, and maybe he'll forgive me for dropping the ball on that last check....
Kurt Huhn
AKA: Oversized Ostrogoth
artisan@k-huhn.com
User avatar
Frank
Posts: 1341
Joined: Thu Nov 23, 2006 8:00 pm
Location: Southern California

Post by Frank »

While we're on the subject of stamps....

I haven't as yet used my stamp, so I was wondering how best to use it. Applying it to the shank, does one use a small hammer to make the imprint? Is there a danger of cracking/crushing the shank if too much force is used?

I've been considering heating the stamp with a propane torch and burning into the briar. Good idea? Yes? No? Maybe? Are you crazy?
Regards,
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett
User avatar
RadDavis
Posts: 2693
Joined: Thu Nov 23, 2006 8:00 pm
Location: united states/Alabama
Contact:

Post by RadDavis »

Hi Frank,

Just push it on by hand gently rocking as you go. It doesn't take near as much pressure as you think.

Don't use a hammer or fire.

Try it on some scrap wood.

Rad
Charl
Posts: 1901
Joined: Mon Jan 07, 2008 3:03 pm
Location: South Africa

Post by Charl »

Just by the way: what does a pipe stamp look like? I haven't come across any photos and actually have no idea. I suppose it must be a bit different than normal stamps though? :?
Patrick
Posts: 62
Joined: Mon Oct 27, 2008 12:21 pm
Location: Texas

Post by Patrick »

Today I purchased a Walmart an $11.00 wood burner pencil. Went home and tried it out. It works great! Lucky that I have a steady hand.
I put the pipe name on shank bottom with fine line pencil first, then went over it with burner and worked out fine. Advantage is that you can use block or script, etc. Not confined to a steel stamp. This burner may not work for every one.
User avatar
Ryan
Posts: 258
Joined: Wed Oct 31, 2007 9:31 pm
Location: Phoenix, AZ

Post by Ryan »

There is a guy here in AZ his name is Howard he is the owner and operator of Starfire engraving. He lazer marks all my pipes. He is very good and reasonable priced.

623-776-0791
pierredekat

Post by pierredekat »

Of all the things I do, putting my mark on a pipe is my least favorite.

Because a poor stamping can sure sure enough turn a masterpiece into a piece of poop in no time at all.

But one thing I have found helpful is putting on some very light pencil guidelines before I do it.

I start with two parallel lines, approximately 1/8 inch apart. And then I mark a little hash mark where the stamp should start and where it should end.

Then I rehearse what I'm going to do in my mind, until I think I can do it in real life. And that's when I put the steel to the wood.

Anywho, I imagine this sort of approach would be applicable with any marking technique: stamping, engraving, etc.
FredS
Posts: 304
Joined: Mon Sep 22, 2008 10:21 pm
Location: Kansas City, USA

Post by FredS »

Frank wrote:While we're on the subject of stamps....

I haven't as yet used my stamp, so I was wondering how best to use it...
Here's how Claudio Cavicchi does it

Image
"Cut your own wood and you warm yourself twice." - Henry Ford
User avatar
Frank
Posts: 1341
Joined: Thu Nov 23, 2006 8:00 pm
Location: Southern California

Post by Frank »

FredS wrote:Here's how Claudio Cavicchi does it
Interesting press gizmo. :idea: Hmm, a drill press, a stamp... experiment time.
Regards,
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett
Post Reply