Sandblast cabinet glass protection.

Sanding, rusticating, sandblasting, buffing, etc. All here.
caskwith
Posts: 2200
Joined: Sat Dec 08, 2007 6:00 am

Sandblast cabinet glass protection.

Post by caskwith »

What do you guys use on the window of your cabinets to stop the glass getting all scratched up?

Up until now I have been using the acetate sheets that came with it. Used the last one and looked into getting some more and boy are they expensive, they want the best part of $10 each!
I looked at buying some plain acetate sheet and that stuff is damn expensive too!

As an experiment I am using a piece of clear vinyl tablecloth. It looks good so far, we will see how it handles a sandblasting session. It is much cheaper than acetate, I can get a piece big enough for 4 covers for about the same price as one acetate, since acetate covers lasted me about 6 months this needs to last at least 2 to be cost effective. Fingers crossed.
User avatar
jogilli
Site Supporter
Posts: 756
Joined: Thu Mar 25, 2010 2:49 pm
Location: Germany
Contact:

Re: Sandblast cabinet glass protection.

Post by jogilli »

Several of the guys over here where I'm at use Saran Wrap... The affix the roll at the top and pull down a clean area every so often .. You just have to be careful not to shot though the Saran Wrap

James
User avatar
baweaverpipes
The Awesomer
Posts: 947
Joined: Tue Dec 19, 2006 8:07 am
Location: Franklin, Tennessee
Contact:

Re: Sandblast cabinet glass protection.

Post by baweaverpipes »

I go to Lowe's or Home Depot and buy glass. Duct tape holds it in place. Depending on the size of your cabinet, buy the size that is best for you.
Considering we work on small pieces, I just buy 8x10 glass and it's about $2 per pane. It lasts a long time.
BAW
BobR
Posts: 225
Joined: Wed Feb 08, 2012 8:37 pm

Re: Sandblast cabinet glass protection.

Post by BobR »

As a noob, I'm always amazed at the little common sense tid bits of knowledge shared here. This is a great forum.
Bob
User avatar
WCannoy
Posts: 542
Joined: Thu Nov 15, 2012 6:58 pm
Location: Lakeland, Florida
Contact:

Re: Sandblast cabinet glass protection.

Post by WCannoy »

caskwith wrote:Up until now I have been using the acetate sheets that came with it.
I just pop mine out and hit it with the buffing wheel.
wdteipen
Posts: 2819
Joined: Sat Mar 29, 2008 1:05 pm

Re: Sandblast cabinet glass protection.

Post by wdteipen »

I stopped using film because I didn't like how it made things less clear. I don't sandblast my glass. That has been working well for the last couple of years. I figure it's cheaper to replace the glass like Bruce mentions.
Wayne Teipen
Teipen Handmade Briar Pipes
http://www.teipenpipes.com
User avatar
Sasquatch
Posts: 5147
Joined: Tue Jan 13, 2009 1:46 am

Re: Sandblast cabinet glass protection.

Post by Sasquatch »

I sandblast by feel. Can't see shit in my cabinet.
ALL YOUR PIPE ARE BELONG TO US!
User avatar
baweaverpipes
The Awesomer
Posts: 947
Joined: Tue Dec 19, 2006 8:07 am
Location: Franklin, Tennessee
Contact:

Re: Sandblast cabinet glass protection.

Post by baweaverpipes »

Sasquatch wrote:I sandblast by feel. Can't see shit in my cabinet.
And..........you forgot to mention, you don't wear gloves! Gloves are for sissies! Right Sas? :ROFL:
User avatar
Sasquatch
Posts: 5147
Joined: Tue Jan 13, 2009 1:46 am

Re: Sandblast cabinet glass protection.

Post by Sasquatch »

They's gloves now?
ALL YOUR PIPE ARE BELONG TO US!
pipedreamer
Posts: 1056
Joined: Mon Jan 07, 2013 6:25 pm

Re: Sandblast cabinet glass protection.

Post by pipedreamer »

At least we have clean fingernails, Right. :rockon:
caskwith
Posts: 2200
Joined: Sat Dec 08, 2007 6:00 am

Re: Sandblast cabinet glass protection.

Post by caskwith »

Obviously glass is a lot cheaper for you guys than it is here for us :(
socrates
Posts: 316
Joined: Tue Dec 31, 2013 1:32 pm
Location: Oahu, Hawaii, USA

Re: Sandblast cabinet glass protection.

Post by socrates »

Harbor Frieght

Sent from my HTC0P3P7 using Tapatalk
User avatar
archaggelosmichail
Posts: 188
Joined: Thu Jul 14, 2011 11:11 am
Location: Paros, Greece
Contact:

Re: Sandblast cabinet glass protection.

Post by archaggelosmichail »

An update to the topic.

I run out of the sheets that came with my blaster and I checked cyclone's site where they suggest Mylar sheets:
http://www.cycloneblasters.com/partsandaccessories.html

Have anyone tried those before? I found them here for 25$ for 50 sheets on the dimensions that I like.
http://www.stencilease.com/db/display.asp?input=1858

Thanks,
Michail
caskwith
Posts: 2200
Joined: Sat Dec 08, 2007 6:00 am

Re: Sandblast cabinet glass protection.

Post by caskwith »

I forgot about this topic.

I bought the PVC clear table cloth and fixed it in place. I not realise that it has been in place for over a year now and it is still pretty good. Acetate sheets used to last me about 3 months or so, the PVC cloth will probably need changing sometime this year maybe. I think I am going to stick with the PVC.
User avatar
archaggelosmichail
Posts: 188
Joined: Thu Jul 14, 2011 11:11 am
Location: Paros, Greece
Contact:

Re: Sandblast cabinet glass protection.

Post by archaggelosmichail »

My sheets last about 90minutes of blast each, I don't know if it is cause of the small cabin height and the table cloth that I used need change in 20minute.

I think that I'm going to try the Mylar sheets and see if it work.
Oakbear
Posts: 103
Joined: Mon Aug 06, 2012 4:47 pm
Location: Nottingham, UK
Contact:

Re: Sandblast cabinet glass protection.

Post by Oakbear »

Chris, sounds like you have it nailed, but if you fancy trying glass have a word with a local glazier. I have a local place that i have contacted for various small projects, and they always do me small sections at a very good price. Maybe not $2, but only a few quid.
User avatar
sandahlpipe
Posts: 2106
Joined: Mon Feb 04, 2013 8:49 pm
Location: Zimmerman, MN
Contact:

Re: Sandblast cabinet glass protection.

Post by sandahlpipe »

I use the replacement sheets from Cyclone and they work well. I do clean the dust off when I put a new sheet on. I replace mine every 3-4 months on average.
---
Fail early, fail often. Your success depends on it.

Jeremiah Sandahl
http://sandahlpipe.com
User avatar
archaggelosmichail
Posts: 188
Joined: Thu Jul 14, 2011 11:11 am
Location: Paros, Greece
Contact:

Re: Sandblast cabinet glass protection.

Post by archaggelosmichail »

sandahlpipe wrote:I use the replacement sheets from Cyclone and they work well. I do clean the dust off when I put a new sheet on. I replace mine every 3-4 months on average.
I didn't see any prices or way to order on their website, how can we buy them? Is there any online retailer maybe?
caskwith
Posts: 2200
Joined: Sat Dec 08, 2007 6:00 am

Re: Sandblast cabinet glass protection.

Post by caskwith »

archaggelosmichail wrote:My sheets last about 90minutes of blast each, I don't know if it is cause of the small cabin height and the table cloth that I used need change in 20minute.

I think that I'm going to try the Mylar sheets and see if it work.

The kind that I bought is very thick and flexible, I think it lasts so long because it acts like electrical tape, it just bounces off.
caskwith
Posts: 2200
Joined: Sat Dec 08, 2007 6:00 am

Re: Sandblast cabinet glass protection.

Post by caskwith »

Oakbear wrote:Chris, sounds like you have it nailed, but if you fancy trying glass have a word with a local glazier. I have a local place that i have contacted for various small projects, and they always do me small sections at a very good price. Maybe not $2, but only a few quid.

I did check with a local company, for the size I need for my cabinet it was going to cost about £5 per sheet, cheaper if I bought more in bulk but then I have to store it somewhere.
Post Reply