Antler
- bandkbrooks
- Posts: 586
- Joined: Sat Aug 09, 2008 12:37 pm
- Location: Georgetown, KY
Antler
A friend just have me a bunch of deer antler. I have no idea where to begin with the stuff other than a mask because I heard repeatedly that it stinks. Any advice is welcome.
Brandon.
Brandon.
Brandon Brooks
__________________________________
"The voices in my head won't let me have any imaginary friends"
Brandon Brooks
Brandon Brooks Pipes
http://www.brandon-brooks.com
__________________________________
"The voices in my head won't let me have any imaginary friends"
Brandon Brooks
Brandon Brooks Pipes
http://www.brandon-brooks.com
Re: Antler
Smell is not THAT bad, but I've heard that it is recommended with breathing mask anyway to reduce horn dust that can be harmful to lungs.
The antlers is quite hard and can be somewhat brittle, at least in my experience so be careful on a lathe. Also it tends to almost melt and get burnt if friction gets to high in the lathe, this makes it even more brittle afterwards.
Don't know if that's what you were looking for but that is some of my knowledge from deer, moose and elk antler
The antlers is quite hard and can be somewhat brittle, at least in my experience so be careful on a lathe. Also it tends to almost melt and get burnt if friction gets to high in the lathe, this makes it even more brittle afterwards.
Don't know if that's what you were looking for but that is some of my knowledge from deer, moose and elk antler
- bandkbrooks
- Posts: 586
- Joined: Sat Aug 09, 2008 12:37 pm
- Location: Georgetown, KY
Re: Antler
Than you. Are you drilling it on the lathe as well? What are you using as a tenon to join it to the shank?
Brandon Brooks
__________________________________
"The voices in my head won't let me have any imaginary friends"
Brandon Brooks
Brandon Brooks Pipes
http://www.brandon-brooks.com
__________________________________
"The voices in my head won't let me have any imaginary friends"
Brandon Brooks
Brandon Brooks Pipes
http://www.brandon-brooks.com
- Joe Hinkle Pipes
- Posts: 804
- Joined: Tue Feb 15, 2011 1:39 am
- Location: Lafayette Indiana
- Contact:
Re: Antler
The smell is very minim as long as you keep it cool. If you overheat or Burn it the smell is ten times worse. Turn a tenon on the briar shank and epoxy the horn or antler on. Same way for a stem inlay.
- bandkbrooks
- Posts: 586
- Joined: Sat Aug 09, 2008 12:37 pm
- Location: Georgetown, KY
Re: Antler
Thank you guys.
Brandon
Brandon
Brandon Brooks
__________________________________
"The voices in my head won't let me have any imaginary friends"
Brandon Brooks
Brandon Brooks Pipes
http://www.brandon-brooks.com
__________________________________
"The voices in my head won't let me have any imaginary friends"
Brandon Brooks
Brandon Brooks Pipes
http://www.brandon-brooks.com
Re: Antler
What he said!fuchi_jeg wrote:The smell is very minim as long as you keep it cool. If you overheat or Burn it the smell is ten times worse. Turn a tenon on the briar shank and epoxy the horn or antler on. Same way for a stem inlay.
- bandkbrooks
- Posts: 586
- Joined: Sat Aug 09, 2008 12:37 pm
- Location: Georgetown, KY
Re: Antler
What are your thoughts about an occasional wipe down or spray with cool water when turning on the lathe / drilling.
Brandon Brooks
__________________________________
"The voices in my head won't let me have any imaginary friends"
Brandon Brooks
Brandon Brooks Pipes
http://www.brandon-brooks.com
__________________________________
"The voices in my head won't let me have any imaginary friends"
Brandon Brooks
Brandon Brooks Pipes
http://www.brandon-brooks.com
Re: Antler
I'd prefer it as dry as possible, it tends to move a bit when drying..
Think you'll do fine by just taking it easy and watch out if it tend to get hot.
Think you'll do fine by just taking it easy and watch out if it tend to get hot.
- Joe Hinkle Pipes
- Posts: 804
- Joined: Tue Feb 15, 2011 1:39 am
- Location: Lafayette Indiana
- Contact:
Re: Antler
I agree. moisture or heat can change the dimensions, probably not a problem when gluing with epoxy, but I have had some changes in mortise and tenon fit.
Re: Antler
It's best to let antler dry/age before turning. One way I use to determine if it's ready to use is by the color. If it has a yellow tint then it's too soon. If it is grayed then it's good to go. It stabilizes with age so you have less chance of splitting down the road. It also looks nicer the older it is.
- BirdAndBear
- Posts: 3
- Joined: Sat Jul 19, 2014 12:50 pm
- Contact:
Re: Antler
Do you need to have a stainless tube inside it (for a longer extension) or can smoke travel through it without being toxic?
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Re: Antler
If you intend to use a long enough piece that the airway will go directly through the antler you might consider stainless steel tubing but it's not toxic so it's not an absolute must. I find that antler has an off taste that it could impart while smoking. That's the main reason I would consider lining it with SS tubing.BirdAndBear wrote:Do you need to have a stainless tube inside it (for a longer extension) or can smoke travel through it without being toxic?
Sent from my iPhone using Tapatalk
Re: Antler
I've worked with ivory, bone and antler. I always wore a respirator when doing so. Ivory is the worst but didn't want to take a chance with any of them. They all smell when they get hot. I have a P100 (hepa) respirator when I work on pipes and such. Already had a severe case of Pneumonia in June. I don't care to repeat chest tubes and a hospital stay again at least for awhile.