Pipe #15

Want to show you work to the world? Want a place to post photos of your work and solicit the opinions of those that have gone before you? Post your work here.
Post Reply
Pillichody
Posts: 42
Joined: Fri May 05, 2017 9:13 am

Pipe #15

Post by Pillichody »

image1.jpeg
image1.jpeg (152.94 KiB) Viewed 2396 times
image2.jpeg
image2.jpeg (147.5 KiB) Viewed 2396 times
image3.jpeg
image3.jpeg (162.98 KiB) Viewed 2396 times
image4.jpeg
image4.jpeg (142.13 KiB) Viewed 2396 times

Please let me know what I can do to get better.
User avatar
sandahlpipe
Posts: 2106
Joined: Mon Feb 04, 2013 8:49 pm
Location: Zimmerman, MN
Contact:

Re: Pipe #15

Post by sandahlpipe »

Focus on straight lines. You can see the light reflections are bowed on the pictures. Those indicate the lines aren't straight. If you're using a flat file for shaping, hold it askew as you're shaping to keep the lines straight. Use a straight edge to check your work. The shank ought to be 100% flat.

The other thing to improve is the finish. The areas that look dull on the stem are indicative of places where it wasn't sanded as well. Especially right behind the button.
---
Fail early, fail often. Your success depends on it.

Jeremiah Sandahl
http://sandahlpipe.com
Pillichody
Posts: 42
Joined: Fri May 05, 2017 9:13 am

Re: Pipe #15

Post by Pillichody »

Thank you. I see what you mean with the light reflection. and the dull area. I will work on the sanding and the straight lines.
DocAitch
Posts: 1113
Joined: Mon Dec 14, 2015 12:44 am
Location: Baltimore, Maryland

Re: Pipe #15

Post by DocAitch »

You also might want to narrow your shank down on the bowl end and define the bottom line so that there is no sag below the main line of the bottom of the shank.
DocAitch
"Hettinger, if you stamp 'hand made' on a dog turd, some one will buy it."
-Charles Hollyday, pipe maker, reluctant mentor, and curmudgeon
" Never show an idiot an unfinished pipe!"- same guy
Pillichody
Posts: 42
Joined: Fri May 05, 2017 9:13 am

Re: Pipe #15

Post by Pillichody »

Thank you DocAitch, I will work on that. That would also give me a better line along the bottom.
User avatar
RickB
Posts: 378
Joined: Fri Jul 20, 2012 1:56 pm
Location: NC

Re: Pipe #15

Post by RickB »

Something I've read on here before - uttered by far smarter men than I - was "there's still a pretty nice pipe hiding in there".
As a newer carver, it's very easy to get a little chickenshit while shaping in fear of getting something too thin or too small. Doing billiards has helped me in this area for sure, but the main thing I've been trying to do is plan well before I start cutting anything, and then repeating to myself while carving "Stick true to the geometry... Don't carve scared..." as a mantra. :lol:
Chronicling my general ineptitude and misadventures in learning pipe making here: https://www.instagram.com/rustynailbriars/
LatakiaLover
Posts: 3124
Joined: Sun Sep 02, 2007 4:29 am
Location: Kansas City, USA
Contact:

Re: Pipe #15

Post by LatakiaLover »

Find a decently shaped pipe to use as a model, and copy it as best you can.

The end.

(Sounds smartass, but it IS the answer, and NOT drawing the straightest possible lines between points is no service to you in the end.)
UFOs must be real. There's no other explanation for cats.
Pillichody
Posts: 42
Joined: Fri May 05, 2017 9:13 am

Re: Pipe #15

Post by Pillichody »

RickB, your right its easy to worry about taking to much off or getting it to thin while shaping.

Latakialover, I will find a shape to copy.

I still struggle with getting the bowl symmetrical.
DocAitch
Posts: 1113
Joined: Mon Dec 14, 2015 12:44 am
Location: Baltimore, Maryland

Re: Pipe #15

Post by DocAitch »

Getting a pipe symmetrical is always the challenge.
It gets a little easier over time, but is always a challenge. There are lots of methods ranging from simple eyeball comparison side to side to silhouette forms to actually using a molding gauge.
I just sent one off to the GKCPC contest that I noted was asymmetric in a photo AFTER it was in the mail. The first thing I did when I got it back was to re cut it.
DocAitch
"Hettinger, if you stamp 'hand made' on a dog turd, some one will buy it."
-Charles Hollyday, pipe maker, reluctant mentor, and curmudgeon
" Never show an idiot an unfinished pipe!"- same guy
Post Reply